[Aug 23, 2023] Get New 156-585 Certification Practice Test Questions Exam Dumps
Real 156-585 Exam Dumps Questions Valid 156-585 Dumps PDF
NEW QUESTION # 43
James is using the same filter expression in fw monitor for CITRIX very often and instead of typing this all the time he wants to add it as a macro to the fw monitor definition file. What's the name and location of this file?
- A. $FWDIR/lib/fw.monitor
- B. $FWDIR/lib/fwmonltor.def
- C. $FWDIR/conf/fwmonltor.def
- D. $FWDIR/lib/tcpip.def
Answer: B
NEW QUESTION # 44
What is the function of the Core Dump Manager utility?
- A. To determine which process is slowing down the system
- B. To limit the number of core dump files per process as well as the total amount of disk space used by core files
- C. To send crash information to an external analyzer
- D. To generate a new core dump for analysis
Answer: B
NEW QUESTION # 45
When a User process or program suddenly crashes, a core dump is often used to examine the problem. Which command is used to enable the core-dumping via GAIA dish?
- A. set core-dump per_process
- B. set core-dump enable
- C. set core-dump total
- D. set user-dump enable
Answer: B
NEW QUESTION # 46
RAD is initiated when Application Control and URL Filtering blades are active on the Security Gateway What is the purpose of the following RAD configuration file SFWDIR/conf/rad_settings.C?
- A. This file contains the information on how the Security Gateway reaches the Security Managers RAD service for Application Control and URL Filtering
- B. This file contains RAD proxy settings
- C. This file contains the location information tor Application Control and/or URL Filtering entitlements
- D. This file contains all the host name settings for the online application detection engine
Answer: A
NEW QUESTION # 47
the difference in debugging a S2S or C2S (using Check Point VPN Client) VPN?
- A. the C2S client uses Browser based SSL vpn and cant be debugged
- B. the C2S VPN can not be debugged as it uses different protocols for the key exchange
- C. the C2S VPN uses a different VPN deamon and there a second VPN debug
- D. there is no difference
Answer: A
NEW QUESTION # 48
You have configured IPS Bypass Under Load function with additional kernel parameters ids_tolerance_no_stress=15 and ids_tolerance_stress-15 For configuration you used the *fw ctl set' command After reboot you noticed that these parameters returned to their default values What do you need to do to make this configuration work immediately and stay permanent?
- A. Set these parameters again with "fw ctl set" and save configuration with "save config"
- B. Use script $FWDIR/bin IpsSetBypass.sh to set these parameters
- C. Edit appropriate parameters in $FWDIR/boot/modules/fwkern.conf
- D. Set these parameters again with "fw ctl set" and edit appropriate parameters in $FWDIR/boot/modules/ fwkern.conf
Answer: D
Explanation:
https://supportcenter.checkpoint.com/supportcenter/portal?eventSubmit_doGoviewsolutiondetails=&solutionid=sk62848&partition=Advanced&product=IPS
NEW QUESTION # 49
What is the benefit of running "vpn debug trunc over "vpn debug on"?
- A. No advantage one over the other
- B. "vpn debug trunc* provides verbose capture
- C. "vpn debug trunc*truncates the capture hence the output contains minimal capture
- D. "vpn debug trunc" purges ike.elg and vpnd elg and creates limestarnp while starting ike debug and vpn debug
Answer: D
NEW QUESTION # 50
Joey is configuring a site-to-site VPN with his business partner. On Joey's site he has a Check Point R80.10 Gateway and his partner uses Cisco ASA 5540 as a gateway.
Joey's VPN domain on the Check Point Gateway object is manually configured with a group object that contains two network objects:
VPN_Domain3 = 192.168.14.0/24
VPN_Domain4 = 192.168.15.0/24
Partner's site ACL as viewed from "show run"
access-list JOEY-VPN extended permit ip 172.26.251.0 255.255.255.0 192.168.14.0 255.255.255.0 access-list JOEY-VPN extended permit ip 172.26.251.0 255.255.255.0 192.168.15.0 255.255.255.0 When they try to establish VPN tunnel, it fails. What is the most likely cause of the failure given the information provided?
- A. Tunnel falls on partner site. It is likely that the Cisco ASA 5540 will reject the Phase 2 negotiation. Check Point continues to present its own encryption domain as 192.168.14.0/24 and 192.168.15.0/24, but the peer expects the one network 192.168.14.0/23
- B. Tunnel fails on partner site. It is likely that the Cisco ASA 5540 will reject the Phase 2 negotiation. Check Point continues to present its own encryption domain as 192.168.14.0/23, but the peer expects the two distinct networks 192.168.14.0/24 and 192.168.15.0/24.
- C. Tunnel falls on partner site. It is likely that the Cisco ASA 5540 will reject the Phase 2 negotiation due to the algorithm mismatch.
- D. Tunnel fails on Joey's site, because he misconfigured IP address of VPN peer.
Answer: B
NEW QUESTION # 51
What is the main SecureXL database for trackingthe acceleration status of traffic?
- A. cphwd_dev_conn_table
- B. cphwd_dev_identity_table
- C. cphwd_db
- D. cphwd_tmp1
Answer: B
NEW QUESTION # 52
What is the difference in debugging a S2S or C2S (using Check Point VPN Client) VPN?
- A. the C2S VPN uses a different VPN daemon and there a second VPN debug
- B. the C2S VPN can not be debugged as it uses different protocols for the key exchange
- C. there is no difference
- D. the C2S client uses Browser based SSL vpn and can't be debugged
Answer: D
NEW QUESTION # 53
Which one of the following is NOT considered a Solr core partition:
- A. CPM_Gtobal_R
- B. CPM_Global_A
- C. CPM_0_Disabled
- D. CPM_0_Revisions
Answer: C
NEW QUESTION # 54
Which daemon governs the Mobile Access VPN blade and works with VPND to create Mobile Access VPN connections? It also handles interactions between HTTPS and the Multi-Portal Daemon.
- A. SSL VPN Daemon - sslvpnd
- B. Mobile Access Daemon - MAD
- C. Connectra VPN Daemon - cvpnd
- D. mvpnd
Answer: C
NEW QUESTION # 55
Which command can be run in Expert mode lo verify the core dump settings?
- A. grep SFWDlR/config/db/initial
- B. grep cdm /config/db/coredump
- C. grep cdm /config/db/initial
- D. cat /etc/sysconfig/coredump/cdm conf
Answer: A
NEW QUESTION # 56
You are trying to establish a VPN tunnel between two Security Gateways but fail. What initial steps will you make to troubleshoot the issue
- A. capture traffic on both tunnel members and collect kernel debug for fw module with vm, crypt, conn and drop flags, then collect debug of IKE and VPND daemon
- B. collect debug of IKE and VPND daemon and collect kernel debug for fw module with vm, crypt, conn and drop flags
- C. capture traffic on both tunnel members and collect kernel debug for fw module with vm, crypt, conn and drop flags
- D. capture traffic on both tunnel members and collect debug of IKE and VPND daemon
Answer: D
NEW QUESTION # 57
Which Threat Prevention daemon is the core Threat Emulator, engine and responsible for emulation files and communications with Threat Cloud?
- A. ted
- B. ctasd
- C. scrub
- D. inmsd
Answer: A
Explanation:
https://supportcenter.checkpoint.com/supportcenter/portal?eventSubmit_doGoviewsolutiondetails=&solutionid=sk97638
NEW QUESTION # 58
Where will the usermode core files be located?
- A. /var/log/dump/usermode
- B. /var/suroot
- C. SCPDIR/var/log/dump/usermode
- D. SFWDlR/var'log/dump/usermode
Answer: A
NEW QUESTION # 59
The two procedures available for debugging in the firewall kernel are
i fw ctl zdebug
ii fw ctl debug/kdebug
Choose the correct statement explaining the differences in the two
- A. (i) is used on a Security Gateway, whereas (11) is used on a Security Management Server
- B. (i) is used to debug only issues related to dropping of traffic, however (n) can be used for any firewall issue including NATing, clustering etc.
- C. (i) is used to debug the access control policy only, however (n) can be used to debug a unified policy
- D. (i) Is used for general debugging, has a small buffer and is a quick way to set kernel debug flags to get an output via command line whereas (11) is useful when there is a need for detailed debugging and requires additional steps to set the buffer and get an output via command line
Answer: D
NEW QUESTION # 60
......
In order to prepare for the CheckPoint 156-585 exam, individuals may choose to take a variety of training courses or study materials. This may include online training courses, self-paced study guides, and practice exams. It is important for individuals to have a strong understanding of network security principles, as well as experience with troubleshooting and resolving security-related issues.
CheckPoint 156-585 exam is a challenging and advanced certification program designed for experienced IT professionals who specialize in Check Point security solutions. Successful candidates will have the skills and knowledge necessary to identify and troubleshoot complex security issues, as well as develop effective solutions to prevent future problems. With its rigorous testing and high standards, the CheckPoint 156-585 exam is a valuable credential for IT professionals seeking to advance their careers in the field of network and security troubleshooting.
156-585 Exam Dumps - PDF Questions and Testing Engine: https://www.pdfvce.com/CheckPoint/156-585-exam-pdf-dumps.html
Latest 156-585 Exam Dumps for Pass Guaranteed: https://drive.google.com/open?id=1o08tnhmHnHljgX1TG4xYFNQ-cc4_yFkG