NACE-CIP2-001 Exam PDF [2026] Tests Free Updated Today with Correct 100 Questions
NACE NACE-CIP2-001 Exam Preparation Guide and PDF Download
NEW QUESTION # 14
When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:
- A. Tooke Gauge
- B. Magnetic Gauge
- C. Ultra Sonic DFT Gauge
- D. Eddy Current Gauge
Answer: A
NEW QUESTION # 15
An Inspection and Test Plan is required when:
- A. It is always required
- B. When the Coating Applicator requests one
- C. When the Inspector requests one
- D. When the Owner specifies one
Answer: A
NEW QUESTION # 16
When ASIN D 3363 is specified the Inspector must:
- A. Use the correct solvent
- B. Record the two end points identified in the standard
- C. Record the highest value attained
- D. Record the percentage of failure
Answer: B
NEW QUESTION # 17
Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
- A. Fusion Bonded Epoxy
- B. 2-Layer Polyethylene (PE)
- C. 3-Layer Polyethylene (PE)
- D. Coal Tar Enamel
Answer: C
NEW QUESTION # 18
Which concrete smoothing technique involves scrubbing a mixture of cement mortar over the concrete surface using ai cement sack, gunny sack, or sponge rubber float?
- A. High-pressure water washing
- B. Stoning
- C. Acid etching
- D. Sacking
Answer: D
NEW QUESTION # 19
The most likely area of failure on a buried external pipeline coating is the:
- A. Ground bed
- B. Field joint coating
- C. Mainline coating
- D. Areas exposed to Ultra Violet light
Answer: B
NEW QUESTION # 20
You are the NACY Coating Inspector on a tank lining project where desiccant dehumidification is being used. Since the first shift of abrasive blasting your readings have indicated relative humidity below 40%; however on the second shift of coating application your readings are indicting 80%.
Your FIRST preferred course of action is to:
- A. Document the readings at the end of the shift
- B. Call your supervisor
- C. Advise the coating applicator supervisor of your readings
- D. Check to See if the dehumidification equipment is operating correctly
Answer: C
NEW QUESTION # 21
Linings are used on the interior of pipelines to
- A. reduce magnetic polarity.
- B. provide protection against soil chemicals.
- C. afford limited temperature insulation.
- D. protect the transported product.
Answer: D
NEW QUESTION # 22
You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind schedule and you are asked to take DIY Film Thickness readings.
Your FIRST preferred course of action is to:
- A. Develop your own methodology and proceed take the readings
- B. Call your supervisor
- C. Refuse to take readings until an is in place
- D. Use a generally accepted industry standard and to take readings
Answer: D
NEW QUESTION # 23
As a NACE Level 2 Inspector on a field job; prior to submission your documentation should always reviewed and approved by:
- A. A NACE Protective Coating Specialist
- B. A NACE Level 3 Inspector
- C. A NACE Level 1 Inspector
- D. Another NACE Level 2 Inspector
Answer: B
NEW QUESTION # 24
The number of air turns in an enclosure can be affected by all of these EXCEPT
- A. coating type.
- B. time of the year (winter/summer).
- C. type of dehumidification equipment (refrigerant or desiccant).
- D. manufacturer of the equipment.
Answer: A
NEW QUESTION # 25
The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of
- A. epoxies.
- B. powder coatings.
- C. urethanes.
- D. inorganic zincs.
Answer: D
NEW QUESTION # 26
Inspector reports should always be copied to:
- A. All parties involved in the project
- B. The Owner only
- C. Whomever the Owner identifies
- D. The Contractor and Owner
Answer: C
NEW QUESTION # 27
You are working as an inspector in a galvanizing plant for the first time.
What are some of the hazards you need to be aware of:
- A. a), b), and c)
- B. Risk of acid or caustic splashes
- C. Risk of chemical exposure
- D. Risk of skin
Answer: A
NEW QUESTION # 28
You have just your NACE CIP Level 2 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Review the NACE Attestation prior to making a decision
- B. Advise the prospective employer that you cannot accept the position
- C. Meet with the prospective employer to scope of your role
- D. Accept assignment without hesitation
Answer: A
NEW QUESTION # 29
Coating application to concrete substrates is:
- A. Not required as Concrete is inorganic
- B. More challenging than coating steel
- C. The same as coating steel
- D. Less challenging, than coating steel
Answer: B
NEW QUESTION # 30
You are the NACE Level 2 inspector reviewing the documentation from a NACE Level 1 you notice significant documentation errors.
Your FIRST preferred course of action is to:
- A. Correct the errors yourself and suggest the Level 1 inspector be replaced
- B. Have the Level 1 Inspector correct the errors and set up remedial training to improve the quality of documentation
- C. Correct the errors yourself and advise your supervisor that the Level 1 Inspector is incompetent
- D. Correct the errors yourself and submit the reports without any further action
Answer: B
NEW QUESTION # 31
All of these are advantages of using repair patches EXCEPT
- A. inert to common acids, alkalis, and solvents.
- B. special tools or equipment are required.
- C. excellent abrasion resistance.
- D. barrier to moisture and corrosion.
Answer: B
NEW QUESTION # 32
Non-Conformance Reports are designed to:
- A. Punish the Contractor for substandard work
- B. Elevate the status of the Inspector
- C. Assist the Owner in negotiating credits from the Contractor
- D. To identify items that do not meet the specification requirements
Answer: D
NEW QUESTION # 33
......
NACE NACE-CIP2-001 is an internationally recognized exam that is designed for coating inspectors who have a good understanding of coating materials, surface preparation, and application techniques. NACE-CIP2-001 exam is intended to evaluate the coating inspector's understanding of the coating inspection process, the ability to identify coating defects, and the ability to interpret coating specifications. Coating Inspector Level 2 certification is recognized in the industry as a standard for coating inspectors, and it is highly sought after by companies that require coatings inspections.
Verified & Correct NACE-CIP2-001 Practice Test Reliable Source Jun 23, 2026 Updated: https://www.pdfvce.com/NACE/NACE-CIP2-001-exam-pdf-dumps.html
Free NACE NACE-CIP2-001 Exam Files Downloaded Instantly: https://drive.google.com/open?id=1Zpf5yaMj3B06SdxvJYE0XYiN5IuBbziV